TY - JOUR
T1 - Investigation of the Mechanical Properties of Quick-Strength Geopolymer Material Considering Preheated-to-Room Temperature Ratio of Sand, Na2SiO3-to-NaOH Ratio, and Fly Ash-to-GGBS Ratio
AU - Bhina, Mohammad Rizwan
AU - Liu, Kuang Yen
AU - Hu, John Eric Hsin Yu
AU - Tsai, Chih Ta
N1 - Publisher Copyright:
© 2023 by the authors.
PY - 2023/3
Y1 - 2023/3
N2 - Geopolymer concrete is a useful alternative construction material for bridge deck systems, as it is characterized by a low carbon footprint, rapid setting, quick strength development, low cost, freeze-thaw resistance, low shrinkage, and sulphate and corrosion resistance. Heat curing enhances the mechanical properties of geopolymer materials (GPM), but it is not suitable for large structures, as it affects construction activities and increases energy consumption. Therefore, this study investigated the effect of preheated sand at varying temperatures on GPM compressive strength (Cs), the influence of Na2SiO3 (sodium silicate)-to-NaOH (sodium hydroxide—10 molar concentration), and fly ash-to-granulated blast furnace slag (GGBS) ratios on the workability, setting time, and mechanical strength properties of high-performance GPM. The results indicate that a mix design with preheated sand improved the Cs of the GPM compared to sand at room temperature (25 ± 2 °C). This was caused by the heat energy increasing the kinetics of the polymerization reaction under similar curing conditions and with a similar curing period and fly ash-to-GGBS quantity. Additionally, 110 °C was shown to be the optimal preheated sand temperature in terms of enhancing the Cs of the GPM. A Cs of 52.56 MPa was achieved after three hours of hot oven curing at a constant temperature of 50 °C. GGBS in the geopolymer paste increased the mechanical and microstructure properties of the GPM as a result of different formations of crystalline calcium silicate (C-S-H) gel. The synthesis of C-S-H and amorphous gel in the Na2SiO3 (SS) and NaOH (SH) solution increased the Cs of the GPM. We conclude that a Na2SiO3-to-NaOH ratio (SS-to-SH) of 5% was optimal in terms of enhancing the Cs of the GPM for sand preheated at 110 °C. Additionally, as the quantity of ground GGBS in the geopolymer paste increased, the thermal resistance of the GPM was significantly reduced.
AB - Geopolymer concrete is a useful alternative construction material for bridge deck systems, as it is characterized by a low carbon footprint, rapid setting, quick strength development, low cost, freeze-thaw resistance, low shrinkage, and sulphate and corrosion resistance. Heat curing enhances the mechanical properties of geopolymer materials (GPM), but it is not suitable for large structures, as it affects construction activities and increases energy consumption. Therefore, this study investigated the effect of preheated sand at varying temperatures on GPM compressive strength (Cs), the influence of Na2SiO3 (sodium silicate)-to-NaOH (sodium hydroxide—10 molar concentration), and fly ash-to-granulated blast furnace slag (GGBS) ratios on the workability, setting time, and mechanical strength properties of high-performance GPM. The results indicate that a mix design with preheated sand improved the Cs of the GPM compared to sand at room temperature (25 ± 2 °C). This was caused by the heat energy increasing the kinetics of the polymerization reaction under similar curing conditions and with a similar curing period and fly ash-to-GGBS quantity. Additionally, 110 °C was shown to be the optimal preheated sand temperature in terms of enhancing the Cs of the GPM. A Cs of 52.56 MPa was achieved after three hours of hot oven curing at a constant temperature of 50 °C. GGBS in the geopolymer paste increased the mechanical and microstructure properties of the GPM as a result of different formations of crystalline calcium silicate (C-S-H) gel. The synthesis of C-S-H and amorphous gel in the Na2SiO3 (SS) and NaOH (SH) solution increased the Cs of the GPM. We conclude that a Na2SiO3-to-NaOH ratio (SS-to-SH) of 5% was optimal in terms of enhancing the Cs of the GPM for sand preheated at 110 °C. Additionally, as the quantity of ground GGBS in the geopolymer paste increased, the thermal resistance of the GPM was significantly reduced.
UR - http://www.scopus.com/inward/record.url?scp=85149660045&partnerID=8YFLogxK
UR - http://www.scopus.com/inward/citedby.url?scp=85149660045&partnerID=8YFLogxK
U2 - 10.3390/polym15051084
DO - 10.3390/polym15051084
M3 - Article
AN - SCOPUS:85149660045
SN - 2073-4360
VL - 15
JO - Polymers
JF - Polymers
IS - 5
M1 - 1084
ER -