每年研究成果
研究成果 1981 2019
- 113個結果中的1 - 50
- 出版年份,標題 (降序)
2019
3D dynamic thermal and thermomechanical stress analysis of a hot blast stove
Gan, Y. F., Jang, J-Y. & Wu, T. Y., 2019 一月 1, (Accepted/In press) 於 : Ironmaking and Steelmaking.研究成果: Article
Stoves
Stress analysis
Linings
Refractory materials
Domes
Analysis of heat transfer enhancement of electrohydrodynamic electrode in a horizontal enclosure
Jang, J. Y., Chen, C. C. & Leu, J. S., 2019 一月 1, 於 : Journal of thermophysics and heat transfer. 33, 4, p. 1176-1180 5 p.研究成果: Article
The heat transfer analysis of an acting-type heat retention panel used in a hot rolling process
Jang, J. Y., Guo, J. W. & Chang, C. C., 2019 一月 7, 於 : Applied Sciences (Switzerland). 9, 1, 189.研究成果: Article
Hot rolling
heat transfer
Heat transfer
temperature gradients
heat
Three-Dimensional Electrohydrodynamic Enhanced Water Evaporation Using Needle-Arrayed Electrodes
Leu, J. S., Jang, J. Y. & Wu, Y. H., 2019 一月 1, (Accepted/In press) 於 : Heat Transfer Engineering.研究成果: Article
Electrohydrodynamics
electrohydrodynamics
needles
Needles
Evaporation
2018
1
引文
(Scopus)
3-D EHD enhanced natural convection over a horizontal plate flow with optimal design of a needle electrode system
Jang, J-Y. & Chen, C. C., 2018 一月 1, 於 : Energies. 11, 7, 1670.研究成果: Article
Electrohydrodynamics
Natural Convection
Natural convection
Needles
3D
Novel Approach to Estimate the Optimum Zone Fuel Mass Flow Rates for a Walking Beam Type Reheating Furnace
Lin, C. N., Luo, Y. P., Jang, J-Y. & Wang, C. H., 2018 五月 9, 於 : Heat Transfer Engineering. 39, 7-8, p. 586-597 12 p.研究成果: Article
walking
mass flow rate
furnaces
Furnaces
Flow rate
Numerical Simulation of a Two-Phase Flow for the Acrylonitrile Electrolytic Adiponitrile Process in a Vertical/Horizontal Electrolysis Cell
Jang, J-Y. & Gan, Y. F., 2018 一月 1, 於 : Energies. 11, 10, 2731.研究成果: Article
Two-phase Flow
Electrolysis
Two phase flow
Current density
Horizontal
Optimisation of a slab heating pattern with various skid button heights in a walking-beam-type reheating furnace
Jang, J-Y. & Huang, J. B., 2018 十月 21, 於 : Ironmaking and Steelmaking. 45, 9, p. 793-804 12 p.研究成果: Article
Furnaces
Heating
Energy utilization
Temperature
Gradient methods
3
引文
(Scopus)
Optimization of the wire electrode height and pitch for 3-D electrohydrodynamic enhanced water evaporation
Leu, J. S., Jang, J-Y. & Wu, Y. H., 2018 三月 1, 於 : International Journal of Heat and Mass Transfer. 118, p. 976-988 13 p.研究成果: Article
Electrohydrodynamics
electrohydrodynamics
mass transfer
Evaporation
Mass transfer
2017
Optimal Heat Transfer Coefficient Distributions during the Controlled Cooling Process of an H-Shape Steel Beam
Gan, Y. F. & Jang, J-Y., 2017 一月 1, 於 : Advances in Materials Science and Engineering. 2017, 9873283.研究成果: Article
Steel
Heat transfer coefficients
Cooling
Gradient methods
Temperature
2016
3
引文
(Scopus)
A Study of an Effective Heat-Dissipating Piezoelectric Fan for High Heat Density Devices
Lin, C. N., Jang, J-Y. & Leu, J. S., 2016 一月 1, 於 : Energies. 9, 8, 610.研究成果: Article
Blade
Fans
Heat
Cantilever
Air
2
引文
(Scopus)
Two dimensional thermal-hydraulic analysis for a packed bed regenerator used in a reheating furnace
Lin, C. N., Jang, J-Y. & Lai, Y. S., 2016 十二月 1, 於 : Energies. 9, 12, 995.研究成果: Article
Packed Bed
Regenerators
Furnace
Packed beds
Hydraulics
2015
26
引文
(Scopus)
Optimization of a slab heating pattern for minimum energy consumption in a walking-beam type reheating furnace
Jang, J. Y. & Huang, J. B., 2015 六月 25, 於 : Applied Thermal Engineering. 85, p. 313-321 9 p., 6547.研究成果: Article
Furnaces
Energy utilization
Heating
Preheating
Temperature distribution
26
引文
(Scopus)
Optimization of louvered-fin heat exchanger with variable louver angles
Jang, J-Y. & Chen, C. C., 2015 十二月 5, 於 : Applied Thermal Engineering. 91, p. 138-150 13 p.研究成果: Article
Heat exchangers
Computer simulation
Conjugate gradient method
Temperature distribution
Infrared radiation
2014
14
引文
(Scopus)
Fractal channel design in a micro methanol steam reformer
Huang, Y. X., Jang, J-Y. & Cheng, C-H., 2014 二月 4, 於 : International Journal of Hydrogen Energy. 39, 5, p. 1998-2007 10 p.研究成果: Article
steam
Fractals
fractals
Methanol
Steam
2013
39
引文
(Scopus)
A study of 3-D numerical simulation and comparison with experimental results on turbulent flow of venting flue gas using thermoelectric generator modules and plate fin heat sink
Jang, J-Y., Tsai, Y. C. & Wu, C. W., 2013 五月 1, 於 : Energy. 53, p. 270-281 12 p.研究成果: Article
Chimneys
Gas generators
Heat sinks
Flue gases
Turbulent flow
76
引文
(Scopus)
Optimization of thermoelectric generator module spacing and spreader thickness used in a waste heat recovery system
Jang, J-Y. & Tsai, Y. C., 2013 一月 1, 於 : Applied Thermal Engineering. 51, 1-2, p. 677-689 13 p.研究成果: Article
Spreaders
Waste heat utilization
Cooling water
Chimneys
Conjugate gradient method
61
引文
(Scopus)
Optimization of the span angle and location of vortex generators in a plate-fin and tube heat exchanger
Jang, J-Y., Hsu, L. F. & Leu, J. S., 2013 九月 18, 於 : International Journal of Heat and Mass Transfer. 67, p. 432-444 13 p.研究成果: Article
vortex generators
tube heat exchangers
Tubes (components)
fins
Vortex flow
2012
25
引文
(Scopus)
Experimental and numerical study of proton exchange membrane fuel cell with spiral flow channels
Jang, J-Y., Cheng, C-H., Liao, W. T., Huang, Y. X. & Tsai, Y. C., 2012 一月 1, 於 : Applied Energy. 99, p. 67-79 13 p.研究成果: Article
channel flow
Proton exchange membrane fuel cells (PEMFC)
Channel flow
fuel cell
Fuel cells
2
引文
(Scopus)
Natural convection in fluid/porous region heated from below with conductive partition
Jang, J-Y., Chou, W. C. & Leu, J. S., 2012 四月 1, 於 : Journal of thermophysics and heat transfer. 26, 2, p. 367-374 8 p.研究成果: Article
free convection
partitions
fluids
thermal conductivity
heat transfer
17
引文
(Scopus)
Optimal design of parallel channel patterns in a micro methanol steam reformer
Jang, J-Y., Cheng, C-H., Huang, Y. X., Lee, C. I. & Leu, C. H., 2012 十一月 1, 於 : International Journal of Hydrogen Energy. 37, 22, p. 16974-16985 12 p.研究成果: Article
steam
Methanol
Steam
methyl alcohol
Chemical reactions
4
引文
(Scopus)
Optimal design of the heat spreader applied thermoelectric module for waste heat recovery
Jang, J-Y., Tsai, Y. C. & Huang, Y. C., 2012 七月, 於 : Advanced Science Letters. 14, 1, p. 253-257 5 p.研究成果: Article
Spreaders
Waste heat utilization
heat
Recovery
Hot Temperature
46
引文
(Scopus)
Parametric study and optimization of louver finned-tube heat exchangers by Taguchi method
Hsieh, C. T. & Jang, J-Y., 2012 九月 1, 於 : Applied Thermal Engineering. 42, p. 101-110 10 p.研究成果: Article
Taguchi methods
Heat exchangers
Heat transfer
Numerical methods
Hydraulics
6
引文
(Scopus)
The three-dimensional simulation and optimization of an integrated power system for reformer-PrOx-fuel cell modeling
Jang, J-Y., Cheng, C-H. & Huang, Y. X., 2012 九月 1, 於 : International Journal of Hydrogen Energy. 37, 18, p. 13797-13805 9 p.研究成果: Article
fuel cells
Fuel cells
Current density
optimization
current density
2011
4
引文
(Scopus)
Effects of non-darcian and inlet conditions on the forced convection along a vertical plate with film evaporation
Leu, J. S., Jang, J-Y. & Chou, W. C., 2011 一月 1, 於 : Heat Transfer Engineering. 32, 11-12, p. 981-987 7 p.研究成果: Article
forced convection
Forced convection
Evaporation
heat transfer
evaporation
2010
76
引文
(Scopus)
An inverse geometry design problem for optimization of single serpentine flow field of PEM fuel cell
Wang, X. D., Huang, Y. X., Cheng, C-H., Jang, J-Y., Lee, D. J., Yan, W. M. & Su, A., 2010 五月 1, 於 : International Journal of Hydrogen Energy. 35, 9, p. 4247-4257 11 p.研究成果: Article
fuel cells
Fuel cells
Flow fields
flow distribution
Cathodes
42
引文
(Scopus)
Effects of porosity gradient in gas diffusion layers on performance of proton exchange membrane fuel cells
Huang, Y. X., Cheng, C-H., Wang, X. D. & Jang, J-Y., 2010 一月 1, 於 : Energy. 35, 12, p. 4786-4794 9 p.研究成果: Article
Diffusion in gases
Proton exchange membrane fuel cells (PEMFC)
Porosity
Oxygen
Water
Experimental and numerical analysis of non-Newtonian effect on film thickness and ribbing instability in forward roll coating process
Jang, J-Y. & Chen, P. Y., 2010 六月 1, 於 : Journal of the Chinese Society of Mechanical Engineers, Transactions of the Chinese Institute of Engineers, Series C/Chung-Kuo Chi Hsueh Kung Ch'eng Hsuebo Pao. 31, 3, p. 221-228 8 p.研究成果: Article
Film thickness
Numerical analysis
Coatings
Wavelength
Applicators
1
引文
(Scopus)
Numerical modeling and design of an inspection device with thermoelectric coolers for the coke oven
Yen, T. H., Jang, J-Y., Chen, Y. B. & Wang, D. H., 2010 一月 1, 於 : Key Engineering Materials. 419-420, p. 29-32 4 p.研究成果: Article
Coke ovens
Inspection
Cameras
Coking
Temperature
23
引文
(Scopus)
Optimal design of baffles locations with interdigitated flow channels of a centimeter-scale proton exchange membrane fuel cell
Jang, J. Y., Cheng, C. H. & Huang, Y. X., 2010 一月 1, 於 : International Journal of Heat and Mass Transfer. 53, 4, p. 732-743 12 p.研究成果: Article
baffles
channel flow
Proton exchange membrane fuel cells (PEMFC)
Channel flow
fuel cells
7
引文
(Scopus)
Optimization of channel width distribution of a gas flow field by integrating computational fluid dynamics code with a simplified conjugate-gradient method
Jang, J-Y., Cheng, C-H. & Huang, Y. X., 2010 一月 21, 於 : Energy and Fuels. 24, 1, p. 570-580 11 p.研究成果: Article
Conjugate gradient method
Flow of gases
Flow fields
Computational fluid dynamics
Flow rate
27
引文
(Scopus)
The effects of geometric and operating conditions on the hydrogen production performance of a micro-methanol steam reformer
Jang, J-Y., Huang, Y. X. & Cheng, C-H., 2010 十月 1, 於 : Chemical Engineering Science. 65, 20, p. 5495-5506 12 p.研究成果: Article
Steam
Hydrogen production
Methanol
Carbon Monoxide
Gases
2009
50
引文
(Scopus)
3D numerical and experimental analysis for thermal-hydraulic characteristics of air flow inside a circular tube with different tube inserts
Chiu, Y. W. & Jang, J. Y., 2009 二月 1, 於 : Applied Thermal Engineering. 29, 2-3, p. 250-258 9 p.研究成果: Article
Die casting inserts
Hydraulics
Tapes
Heat transfer coefficients
Heat transfer
42
引文
(Scopus)
3-D Transient conjugated heat transfer and fluid flow analysis for the cooling process of sintered bed
Jang, J-Y. & Chiu, Y. W., 2009 十月 1, 於 : Applied Thermal Engineering. 29, 14-15, p. 2895-2903 9 p.研究成果: Article
Flow of fluids
Nusselt number
Heat transfer
Cooling
Porosity
9
引文
(Scopus)
Convection heat and mass transfer along a vertical heated plate with film evaporation in a non-Darcian porous medium
Leu, J. S., Jang, J-Y. & Chou, W. C., 2009 十一月 1, 於 : International Journal of Heat and Mass Transfer. 52, 23-24, p. 5447-5450 4 p.研究成果: Article
mass transfer
Porous materials
Evaporation
convection
Mass transfer
35
引文
(Scopus)
Flow field optimization for proton exchange membrane fuel cells with varying channel heights and widths
Wang, X. D., Huang, Y. X., Cheng, C-H., Jang, J-Y., Lee, D. J., Yan, W. M. & Su, A., 2009 九月 30, 於 : Electrochimica Acta. 54, 23, p. 5522-5530 9 p.研究成果: Article
Proton exchange membrane fuel cells (PEMFC)
Flow fields
Conjugate gradient method
Fuel cells
Cathodes
3
引文
(Scopus)
Hall effect on the heat and mass transfer with mhd natural convection from a vertical plate in porous medium
Jang, J-Y. & Hsu, C. T., 2009 十月 1, 於 : Journal of the Chinese Society of Mechanical Engineers, Transactions of the Chinese Institute of Engineers, Series C/Chung-Kuo Chi Hsueh Kung Ch'eng Hsuebo Pao. 30, 5, p. 371-380 10 p.研究成果: Article
Hall effect
Natural convection
Porous materials
Mass transfer
Heat transfer
2
引文
(Scopus)
Reverse roll coating flow with non-Newtonian Fluids
Jang, J-Y. & Chen, P. Y., 2009 一月 1, 於 : Communications in Computational Physics. 6, 3, p. 536-552 17 p.研究成果: Article
coatings
fluids
film thickness
thickness ratio
rations
1
引文
(Scopus)
Ribbing instability analysis of forward roll coating
Lie, K. N., Chiu, Y. M. & Jang, J-Y., 2009 一月 1, 於 : Journal of Mechanics. 25, 2, p. 167-175 9 p.研究成果: Article
Coating
coatings
Coatings
Viscosity
viscosity
7
引文
(Scopus)
Vortex instability of MHD natural convection flow over a horizontal plate in a porous medium
Jang, J-Y. & Hsu, C. T., 2009 二月 1, 於 : Computers and Fluids. 38, 2, p. 333-339 7 p.研究成果: Article
Magnetohydrodynamics
Natural convection
Porous materials
Vortex flow
Radiation effects
2008
24
引文
(Scopus)
3-D numerical and experimental analysis for airflow within a passenger compartment
Chien, C. H., Jang, J-Y., Chen, Y. H. & Wu, S. C., 2008 八月 1, 於 : International Journal of Automotive Technology. 9, 4, p. 437-445 9 p.研究成果: Article
Air
Thermal comfort
Vents
Cooling
Temperature distribution
43
引文
(Scopus)
3-D numerical and experimental analysis of a built-in motorized high-speed spindle with helical water cooling channel
Chien, C. H. & Jang, J-Y., 2008 十二月 1, 於 : Applied Thermal Engineering. 28, 17-18, p. 2327-2336 10 p.研究成果: Article
Cooling water
Temperature distribution
Regression analysis
Printed circuit boards
Heat transfer coefficients
1
引文
(Scopus)
Effect of a magnetic field on vortex instability of natural convection flow over a horizontal plate with blowing and suction
Leu, J. S. & Jang, J-Y., 2008 一月 1, 於 : Journal of the Chinese Institute of Engineers, Transactions of the Chinese Institute of Engineers,Series A/Chung-kuo Kung Ch'eng Hsuch K'an. 31, 5, p. 879-884 6 p.研究成果: Article
Blow molding
Natural convection
Vortex flow
Magnetic fields
Mass transfer
2007
11
引文
(Scopus)
3-D thermal-hydraulic analysis for airflow over a radiator and engine room
Hsieh, C. T. & Jang, J-Y., 2007 十月, 於 : International Journal of Automotive Technology. 8, 5, p. 659-666 8 p.研究成果: Article
Radiators
Heat flux
Hydraulics
Engines
Cooling systems
5
引文
(Scopus)
Effects of magnetohydrodynamics on the vortex instability of natural convection flow over a horizontal plate in a saturated porous medium
Jang, J-Y. & Hsu, C. T., 2007 二月 1, 於 : Journal of the Chinese Society of Mechanical Engineers, Transactions of the Chinese Institute of Engineers, Series C/Chung-Kuo Chi Hsueh Kung Ch'eng Hsuebo Pao. 28, 1, p. 61-70 10 p.研究成果: Article
Magnetohydrodynamics
Natural convection
Porous materials
Vortex flow
Boundary layer flow
4
引文
(Scopus)
Numerical and experimental studies of thin liquid film flow between two forward-rollers
Chien, C. H. & Jang, J-Y., 2007 一月 1, 於 : Journal of Mechanical Science and Technology. 21, 11, p. 1892-1900 9 p.研究成果: Article
Liquid films
Thin films
Coatings
Film thickness
Experiments
62
引文
(Scopus)
Numerical and experimental thermal analysis for a metallic hollow cylinder subjected to step-wise electro-magnetic induction heating
Jang, J-Y. & Chiu, Y. W., 2007 八月 1, 於 : Applied Thermal Engineering. 27, 11-12, p. 1883-1894 12 p.研究成果: Article
Induction heating
Electromagnetic induction
Thermoanalysis
Temperature
Pipe
2006
46
引文
(Scopus)
3-D thermal-hydraulic analysis for louver fin heat exchangers with variable louver angle
Hsieh, C. T. & Jang, J. Y., 2006 十月 1, 於 : Applied Thermal Engineering. 26, 14-15, p. 1629-1639 11 p.研究成果: Article
Heat exchangers
Hydraulics
Heat transfer
Friction
Numerical analysis
29
引文
(Scopus)
Heat and mass transfer for liquid film evaporation along a vertical plate covered with a thin porous layer
Leu, J. S., Jang, J-Y. & Chou, Y., 2006 六月 1, 於 : International Journal of Heat and Mass Transfer. 49, 11-12, p. 1937-1945 9 p.研究成果: Article
Liquid films
mass transfer
Evaporation
Mass transfer
heat transfer
2005
19
引文
(Scopus)
3D Numerical heat transfer and fluid flow analysis in plate-fin and tube heat exchangers with electrohydrodynamic enhancement
Lin, C. W. & Jang, J-Y., 2005 五月 1, 於 : Heat and Mass Transfer/Waerme- und Stoffuebertragung. 41, 7, p. 583-593 11 p.研究成果: Article
tube heat exchangers
Electrohydrodynamics
electrohydrodynamics
Fins (heat exchange)
Tubes (components)